What is a slitting machine:

The slitting machine is a kind of wide-width paper, mica tape Or the mechanical equipment that cuts the film into a plurality of narrow-width materials, which are commonly used in papermaking machinery, wire and cable mica tape and printing and packaging machinery.

The main application of slitting machine is:

Paper, insulation and film Slitting, especially suitable for slitting of narrow strips (insulation materials, mica tape, film, etc.).

The characteristics of the slitter:

The main characteristic of the slitter is the magnetic powder clutch. As a resistance installation, it is controlled by the system to output a DC voltage to control the resistance generated by the magnetic powder clutch. The main advantage is that it is passively mounted and can control small tensions.

Maintenance and maintenance of slitting machine:

Automatic before use The main components are inspected and filled with smooth oil. When inspecting the disassembly and assembly of automatic slitting machine, it is strictly forbidden to use unsuitable tools and unscientific operation methods; once every two weeks, the machine is thoroughly cleaned and inspected; fully automatic If the slitting machine is not used for a long time, it is necessary to wipe all the bright exteriors, apply anti-rust oil, and cover the whole machine with a plastic cover.

If the automatic slitting machine is deactivated for more than 3 months, the anti-rust oil should be covered with moisture-proof paper; after the work is completed, carefully clean the equipment, and Wipe off the exposed rubbing surface and add smooth oil. For daily maintenance, it is necessary to do the following points for the daily maintenance and maintenance of the slitting machine.

First, the electrical parts should be cleaned and inspected regularly;

Use high-quality slitting cutters and cross-cutting knives;

Three, the daily maintenance of the slitting machine should be in place, the standard rope is, lubrication, cleaning, liquidation (no dust, no debris) in place to ensure that the sliding part of the device is in good condition;

Four, maintenance work, stop the rotation part regularly and Irregular inspections.

Operating procedure for slitting machine:

1. The operator must first train again. To work, you must be familiar with the application of different slitting machines! Equipment performance and general maintenance methods. Non-employee personnel are not allowed to operate at will;

2. Do a good job of labor protection before starting the machine, and prepare some auxiliary tools and materials for operation (tool adjustment tool, Carton, paper tube, paper cutter, tape, etc. for job request) and placed in a suitable position on the machine;

3. Make sure the device is safe. ,

Check if the circuit is free of phase air flow, test the machine, and check whether the electrical, pneumatic and mechanical equipment are running normally. Whether the mechanical protection facilities are perfect. Prevent crushing, scratching or bringing in rotating gears, chains, rollers, etc. during operation;

4. Adjusting the knife: Adjusting the accuracy according to the job request The knife distance, pay attention to the direction of the knife edge. If necessary, remove the bottom knife and re-arrange the knife. The knife has a gap or a sharp point to actually repair and change;

5. Investigate static electricity elimination equipment and machine The connection of the ground wire ensures that the static electricity of the data is eliminated during operation. Put the waste paper under the machine to avoid dust adsorption;

6. Pay attention to safety when loading. Push the material to the appropriate position to stop the inflation, and note that the direction of rotation of the material cannot be reversed;

7. Paper and opposite: set the data according to the device The direction is from unwinding to winding, and adjusting the correcting position to stop the opposite side. When cutting the edge, ensure that both sides of the finished product have glue. Be sure to pay attention to the correcting stroke when loading. Be sure to go to the middle of the correction stroke. When you are running, pay attention to correcting one side. When you exceed the stroke, you will need to deal with it immediately;

8. Put on the paper tube of the job request on the take-up reel and align the data. It is necessary to apply double-sided tape to the double-sided adhesive, adjust the appropriate winding tension and unwinding tension, and cut the edge;

9 In the process of winding up, the quality of the product should be strictly checked. The defective products and other wastes or side products should not be rolled into the product, and the number of meters should be strictly controlled;

 11. According to the production requirements, complete the corresponding packaging, including labeling plus wrapping paper or film, sealing, batch number, etc.;

 12. After shutdown, turn off the power supply and air supply, and perform necessary cleaning and maintenance on the machine. The glue on the surface should be wiped clean with solvent;

 13. Problems encountered during the operation, In principle, the shutdown process, the failure to stop the process must be decelerated and carefully handled.

<>